ABS Sensors

An ABS Sensor measures the speed of wheel rotation under braking. ABS works on the principle of braking a wheel until it just begins to skid (this is the point where braking efficiency would drop off dramatically) and then releasing the brake pressure and re-applying the brakes. ABS sensors identify the skid point and trigger a release in brake pressure. As the cycle is repeated many times a second, the driver will feel a rapid pulsing and hear a chattering noise as ABS is applied.

Brake Adjusters

For drum brakes to function correctly, the brake shoes must remain close to the drum without touching it. If they get too far away from the drum (as the shoes wear down, for instance), the piston will require more fluid to travel that distance, and the brake pedal will sink closer to the floor when the brakes are applied. This is why most drum brakes have an automatic adjuster.

Each time the car stops while in reverse, the shoe is pulled tight against the drum. When the gap gets big enough, the adjusting lever rocks enough to advance the adjuster gear by one tooth. The adjuster has threads on it, like a bolt, so that it unscrews a little bit when it turns, lengthening to fill in the gap. When the brake shoes wear a little more, the adjuster can advance again, so it always keeps the shoes close to the drum.

Brake Cables

Brake cables are used to activate the brakes.

Brake Calipers

The brake caliper is the assembly which houses the brake pads and pistons. The pistons are usually made of aluminum or chrome-plated steel. There are two types of calipers: floating or fixed. A fixed caliper does not move relative to the disc. It uses one or more pairs of opposing pistons to clamp from each side of the disc, and is more complex and expensive than a floating caliper. A floating caliper (also called a “sliding caliper”) moves with respect to the disc, along a line parallel to the axis of rotation of the disc; a piston on one side of the disc pushes the inner brake pad until it makes contact with the braking surface, then pulls the caliper body with the outer brake pad so pressure is applied to both sides of the disc.

Brake Disks

The disc brake or disk brake is a device for slowing or stopping the rotation of a wheel. A brake disc (or rotor in U.S. English), usually made of cast iron or ceramic composites (including carbon, kevlar and silica), is connected to the wheel and/or the axle. To stop the wheel, friction material in the form of brake pads (mounted on a device called a brake caliper) is forced mechanically, hydraulically, pneumatically or electromagnetically against both sides of the disc. Friction causes the disc and attached wheel to slow or stop.

  • Precision made to exacting specifications for uniform thickness and hardness.
  • High-quality castings and materials withstand constant heating and cooling.
  • Apec discs are highly resistant to warping.Matching new Apec discs with
  • Apec pads ensures the best possible results. Apec drums are highly resistant to cracking and deformation.
  • Apec Brake Drum from Component Distributors

Brake Drums

A drum brake is a brake in which the friction is caused by a set of shoes or pads that press against the inner surface of a rotating drum. The drum is connected to a rotating wheel.

Brake Pad Fitting Kits

  • Comprehensive range of fitting kits to support Apec pads and shoes.
  • Recommended for better brake stability and safety.
  • A valuable extra profit opportunity.

Brake Hoses

  • EPDM and twin PVA braid construction for superior dependability.
  • End fittings are corrosion-protected using environmentally friendly materials.
  • Production samples regularly assessed with whip, burst and endurance tests.

Master Cylinders

The master cylinder is a control device that converts physical pressure (commonly from a driver’s foot) into hydraulic pressure to operate other device(s) in the hydraulic system. The most common automotive uses of master cylinders are in brake and clutch systems. The operated device in the clutch system is called the slave cylinder. In brake systems, the operated devices are brake calipers and/or wheel cylinders.

  • Latest EPDM seal and boot materials provide outstanding heat, ozone and weather resistance.
  • Precision manufactured for consistently easy fitting and reassuring reliability.
  • High-grade steel or aluminium pistons treated or anodised for improved strength and durability.

Brake Pads

Brake pads are an important part of braking systems for all types of vehicles that are equipped with disc brakes. Brake pads are steel backing plates with friction material bound to the surface facing the brake disk.

Apec

  • Only Apec offers an entire range of High-Pressure Treatment (HPT) scorched pads, for: • superior initial performance and easier bedding-in • longer working life, and optimum safety and comfort.
  • Friction material, back plate and shim production combined in-house for complete quality assurance.
  • High specification shims meet the demands of specific braking systems.
  • Advanced robotic technology ensures precise standards for quick, easy fitting.

Brake Pad Wear Indicators

  • The widest range of replacement wear sensors.
  • Made to exacting OE standards.
  • Unique part identifiers for easy, accurate ordering.

Brake Shoes

The brake shoe carries the brake lining, which is riveted or glued to the shoe. When the brake is applied, the shoe moves and presses the lining against the inside of the drum. The friction between lining and drum provides the braking effort and energy is dissipated as heat. Modern cars have disc brakes all round, or discs at the front and drums at the rear. An advantage of discs is that they can dissipate heat more quickly than drums so there is less risk of overheating. The reason for retaining drums at the rear is that a drum is more effective than a disc as a parking brake.

  • Latest formulation friction materials for maximum stopping power and endurance.
  • Advanced automated production ensures consistently high quality.
  • High strength phenol adhesive for maximum shear values.
  • High resistance varnish gives all metal parts superior rust protection.
  • Supplied fitted with adjusters where appropriate.